49526 / 01INSTALLATION GUIDE • GUÍA DE INSTALACIÓNRQACDBEFGHJMLNPKTools NeededHerramientas necesariasAAAAAAAAUse and programming instructions are loca
MInsert key and test latch. If latch does not extend or retract smoothly, adjust screws (H). Remove key when finished and make sure the latch bolt is
MInsert key and test latch. If latch does not extend or retract smoothly, adjust screws (H). Remove key when finished and make sure the latch bolt is
Z-Wave locks only: Temporarily install battery packSolo cerraduras Z-Wave:Instale temporalmente el conjunto de baterías Perform the Inclusion Proces
Z-Wave locks only: Temporarily install battery packSolo cerraduras Z-Wave:Instale temporalmente el conjunto de baterías Perform the Inclusion Proces
JJLay excess cable flat inside the bottom of the interior housing (J).Acomode el exceso de cable en el fondo del alojamiento interior (J).Ensure tight
JJLay excess cable flat inside the bottom of the interior housing (J).Acomode el exceso de cable en el fondo del alojamiento interior (J).Ensure tight
A BLYESSiNONoNote: “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. “Exclusion” refers to the process in
A BLYESSiNONoNote: “Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller. “Exclusion” refers to the process in
MNPQx3ball tippunta de bolaIf needed, rekey the lock to work with your existing key. See the supplied SmartKey Rekey instructions for more information
MNPQx3ball tippunta de bolaIf needed, rekey the lock to work with your existing key. See the supplied SmartKey Rekey instructions for more information
Options for Select Models OnlyOpciones solamente para modelos selectosDo not use electric drill or electric screwdriver to tighten screws.No utilice e
FoldDoble1-3/4" (44 mm)1-3/8" (35 mm)2-3/8" (60 mm)2-3/4" (70 mm)Edge • Borde BacksetDistancia al centroFace • Frente CenterlineLi
FoldDoble1-3/4" (44 mm)1-3/8" (35 mm)2-3/8" (60 mm)2-3/4" (70 mm)Edge • Borde BacksetDistancia al centroFace • Frente CenterlineLi
Options for Select Models OnlyOpciones solamente para modelos selectosDo not use electric drill or electric screwdriver to tighten screws.No utilice e
1"25 mm2-1/8"54 mm1-1/2"38 mm1-3/8" – 1-3/4"35 mm – 44 mm2-3/8" (60 mm)or • o 2-3/4" (70 mm)oro180°Check Dimensions
1"25 mm2-1/8"54 mm1-1/2"38 mm1-3/8" – 1-3/4"35 mm – 44 mm2-3/8" (60 mm)or • o 2-3/4" (70 mm)oro180°Check Dimensions
1-1/2"38 mmATest if latch bolt fully extends and retracts. Chisel out area inside hole as needed so latch can operate smoothly.Pruebe si el perno
1-1/2"38 mmATest if latch bolt fully extends and retracts. Chisel out area inside hole as needed so latch can operate smoothly.Pruebe si el perno
GECable goes underneath latchEl cable va por debajo del pestilloRoute cable through center hole, then push cable into bottom hole.Conecte el cable a t
GECable goes underneath latchEl cable va por debajo del pestilloRoute cable through center hole, then push cable into bottom hole.Conecte el cable a t
Kommentare zu diesen Handbüchern